Home > Underfloor Heating > Underfloor Heating Sensor Not Working

Underfloor Heating Sensor Not Working

Contents

Contact the manufacturer. If your mat is outside the range on the nameplate label, call the manufacturer. Can I use a room thermostat to activate the heating mat (via the existing programmable controller) or is the only option to lift tiles and replace the sensor? ericmark, 15 Jul 2011 #5 Anneliese Joined: 3 Sep 2010 Messages: 11 Thanks Received: 0 Location: Bedfordshire Country: mointainwalker said: ↑ Did you test to see if the heating worked before check over here

How on earth can you repair underfloor heating if it goes wrong or stops working? Durston has had involvement in multiple construction defect litigation cases. Competitions Time Post, phone & text comps Regular Competitions Compers Chat Corner I won! If a failure point is located, a repair splice can be made. http://www.fitcreative.co.uk/blog/index.php/can-repair-underfloor-heating/

Electric Underfloor Heating Not Working

Disconnect the system's power leads from the control. If the UFH is only a low wattage 'comfort' heater then a room sensor may not be necessary. But I do know that electricians experienced with underfloor heating systems can find these faults and fix them when the location of the fault is unknown. Check the insulation below the UnderFloor system, particularly at the ends of the heated joist bays and verify there are no gaps in the insulation where warm air could escape.

A loose connection can cause a GFI trip. It's a pity it wasn't the other way round then you should have been okay. Use an amp meter to determine if each ProMelt cable is pulling the proper amperage for the specific size of cable(s) you are working on. Warmup Thermostat Not Working Call the manufacturer to discuss the options for achieving this.

With the bath panel off we were able to see the wall was damp so went ahead with the work. If you are using an older meter, it may just need new batteries. melb View public profile Send private message Find more posts View all thanked posts #13 16th Feb 13, 2:31 PM #13 16th Feb 13, 2:31 PM yes http://www.suntouch.com/support/troubleshooting/ Secondly, this winter I have noticed that the thermostat does not activate the heating until its increased to 20 degrees.

andyhop View public profile Send private message Find more posts View all thanked posts #8 16th Feb 13, 9:19 AM #8 16th Feb 13, 9:19 AM “ Electric Underfloor Heating Not Working Properly Even though a thermostat can appear to be operational it might not necessarily be functioning correctly. This is used to avoid wasting electricity when some ProMelt systems may not be capable of melting snow/ice during periods of extreme cold. Let it cure fully before continuing with the installation.

Underfloor Heating Thermostat Not Working

I need help When looking at the Warmup insulation boards, what does the R value mean? find more info Verify your meter is still working and properly calibrated by holding the test leads directly together to test the meter's "zero reading". Electric Underfloor Heating Not Working You can use the thermostat control as a test tool with the floor warming cable by running a brief "Power Test". Electric Underfloor Heating Problems Solving We do our very best not to damage the tiles, but it normally does break.

Loading... check my blog But he is not really worried if it works or not only that it is safe. Is there a lamp, a "space heater", a heat duct, or some other heat source close to the control? Set your ohmmeter on a scale that goes high enough to test the product you have. Warm Up Underfloor Heating Problems

One of the 7m2 mats has stopped heating and there is no resistance at the thermostat end of the tail. Refer to wiring diagram on back of control. "Line side" wires connect to incoming power from the breaker panel and "load side" wires connect to the floor warming system power leads. most controllers have an inbuilt memory or backup battery to keep the settings. this content If you have any questions please read our Forum Rules and FAQs.

At times when the air temperature outside is too cold, some ProMelt systems may not be able to overcome the heat loss to the ground and air, or it may just Underfloor Heating Sensor Resistance Heat loss calculations are normally carried out by a builder, an architect or a heating engineer. With the floor free of obstacles and debris, turn the power on at the breaker panel and observe with both digital and IR video.

We have also pressed the "reset" button on the control panel but no luck.

You can use a thin layer of a 100% silicone sealant, or two or three coats of a heat rated "liquid electric tape" to re-seal the jacket. Once this circuit path is broken, partial heating or no heating will occur. It was also quickly noted that the mats had been working prior to carpet installation. Underfloor Heating Control Problems Even if a manufacturer selling online claims that they offer long warranties, these will be no use if the company does not exist when the warranty may be needed.   We

All work undertaken by UFH Services Ltd is guaranteed for 12 months. You may have to contact the manufacturer, supplier or installer of your underfloor heating mat to authorise a visit by the specialist UFH electrician. Case #3 BCRA conducted its investigation during three site visits. http://techese.net/underfloor-heating/underfloor-heating-one-zone-not-working.html Yes we can locate the problem down to within a few millimetres and, with minimal damage, repair the system.

Sign in Transcript Statistics 6,467 views 1 Like this video? I'm wondering if it might have shorted out because the reason we had all the refurb work done in the first place is because we have a leak coming through the If the temperature outside is too cold, your ProMelt system may not be able to create enough heat to overcome the heat loss to the environment at that time. The floor temperature sensor may not be connected to the control properly.

Thanks Reply Susan says: April 25, 2015 at 1:49 pm Hi Fabian The good thing is that your underfloor heating is working. PS I don't suppose that anything has been screwed into the floor since the installation was done? Question 3: Do you have any suggestion on how to fix it? I need help With the electrical connections, how many heaters can be wired to the thermostat before the junction box is needed?

We have a foil system which is under wood, can this be repaired? Your Ohmmeter may be on the wrong scale. Is it in proper resistance range for the present floor temperature? With the insulation boards, the floor on a concrete base will heat up within 30 minutes to an hour.

We have rental tools to help locate the damage, and we have splice kits to repair the cable after the location of the damage has been determined. Every single one. and why only at night? What is the warranty given by the manufacturer?

We recommend checking out the terms of your manufacturers guarantee. Is it possible more than one cable may have been wired together in series or in parallel? If the zero reading from your meter is not significantly less than 1 ohm, try to obtain a multi-meter with a smaller margin of error before proceeding. In the new part of the kitchen we will be installing electric underfloor heating and ideally then tiles to match the existing floor.

Disconnect the floor temperature sensor and test it with a digital multi-meter able to test up to 20,000 ohms (20k Ω) as described in our installation manual.