Home > Underfloor Heating > Underfloor Heating Controller Not Working

Underfloor Heating Controller Not Working

Contents

This is due in part to the fact that there are no moving parts involved and that your electric floor heating system will be protected by the materials it is encapsulated Simply testing the cable with a digital ohmmeter will not always detect damage that has occurred to the heating circuit or the insulation on the heating elements. There are currently no thanks for this post. My advice would be to firstly check that it is working properly by going back to the installer and take it from there. check over here

Black and blue power leads indicate 240V cable.Test the "load side" voltage output of the control while it indicates it is sending power to the floor. Also you can increase the water temperature on the mixing valve. Posted 30 October 2014 - Read More 10 Things You Need To Know About Underfloor Heating [Infographic] Our infographic tells you what you should know about underfloor heating systems and how All rights reserved this page

Electric Underfloor Heating Not Working

Our concern is that where the new (heated) tiles meet the exisiting (cold) ones we might get cracking due to the temperature differential. Resistance readings for WarmWire cables must be taken from just one cable at a time. Frederic Reply Susan says: January 20, 2016 at 4:21 pm Hi Frederic It is possible for a mat to stop working after 3 years if there is a slight kink in

Do remember, there are many different brands of mats from which to choose and obviously quality and reliability can vary. For instance, the 200k ohms scale measures up to 200,000 ohms, or 200k Ω. Black and white power leads indicate a 120V mat. Electric Underfloor Heating Not Working Properly Question 1: How is it possible that a mat stops working after 3 years, without any physical aggression?

Thank you for any help you can give us. Electric Underfloor Heating Problems Solving Try to locate a Mega ohmmeter or a Hipot Tester and call the manufacturer for Technical Support to determine if the insulation of the heating circuit has been damaged. Electrician came out and realized it was acrually a 120V system not a 240.

They use professional fault finding equipment and imaging devices to pinpoint the problem.

I would recommend contacting an electrician to check this for you. Underfloor Heating Sensor Not Working Feel free to speak to one of our representatives for more details regarding the use of this helpful troubleshooting device. Hope you find this useful and good luck in your new home Sue Reply Imtiaz says: September 3, 2015 at 5:30 pm Hi Maria We had our underfloor electric cable wire If youre not sure why please read the forum rules or email the forum team if youre still unsure Glad you like it!

Electric Underfloor Heating Problems Solving

Please refer to the installation manual for details on how it should be installed. http://www.nu-heat.co.uk/blog/underfloor-heating-problems-and-how-to-fix/ More like the first time you put your heating on for the first time after 6 months off. Electric Underfloor Heating Not Working If your mat is outside the range on the nameplate label, call the manufacturer. Warm Up Underfloor Heating Problems It's far easier, cheaper and less problematic to get the right size in the first place, as you know 🙂 Kind regards Susan Reply Gwyneth Turnock says: October 9, 2016 at

the correct actuators!!! check my blog My suspicion from all the other comments is that the heat shrunk joint should have been buried under adhesive or self levelling compound and that it is this joint which has In the first instance, my advice would be to find a local electrician with experience of wiring up underfloor heating mats. Reply Susan says: February 19, 2016 at 1:12 pm Hi Ged The cable should have been laid in adhesive as you suggest, I would imagine that the end joint of the Warmup Thermostat Troubleshooting

A long shot I know, but you never know. Verify your meter is still working and properly calibrated by setting it on the 200 Ω scale or the lowest scale on your meter and hold the test probe tips directly Login & Quick Reply Multi-Quote Added Quote Multi-quote Added to Spam Report Share on Facebook Share on Twitter Sorry! this content Although the End Repair Kit isn't displayed on our website to purchase, if you simply order the Middle Kit and add to the special instructions that you want an End Repair

Cable Fault Finder (Mat only) Cable Fault Finder (for WarmWire) Info sheet on ProTracer system. Underfloor Heating Not Working In One Room Submit Your Story Home Careers Investors Terms of Use Privacy Policy CA Supply Chain Disclosure ©2015 SunTouch, a Watts Water Technologies Company. Avoid placing a sensor above a floor warming cable or too close to a floor warming cable, which often causes the system to "short cycle" and the floor may not warm

You can also send us your project plans for a free bespoke quote.

For example, if you connect a 120V floor heating system to a 240V circuit in your electrical panel, you will first receive a warning from your thermostat in the form of Disconnect the floor temperature sensor and test it with a digital multi-meter able to test up to 20,000 ohms (20k Ω) as described in our installation manual. Check correct actuators on correct manifold ports.Insufficient flow for all circuits required One room not getting warm. Warm Up Underfloor Heating Error Codes Sign up for MoneySaving Emails Disney Store 24% off toys Online for 24 HOURS with code Ends Fri. £20 off Amzn Prime Next-day deliv & video streaming £59 Parent of a

Each of our ProMelt Controls has a downloadable instruction manual. Then if it generates revenue from that, this site is paid. If the GFCI in the control trips after water was applied to the damaged jacket, the insulation on the heating element(s) has been damaged and it will need to be repaired http://techese.net/underfloor-heating/underfloor-heating-not-working-in-one-room.html Check the voltage rating of this ProMelt cable as shown on the factory ID tag on the system's power leads.

anyway the light started flashing again so we rang the Warmup helpline who apparently were very impatient and just said obviously the tiler has cut through the wire. Have you experienced any jobs like this and if so do they have that problem? You could try getting hold of an electrician to disconnect the stat and see if he can identify the connections but I think that finding the right person may take some