Home > Turn Signal > Trailer Lights Right Blinker Not Working

Trailer Lights Right Blinker Not Working

Contents

What a pain this all was! Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... It requires you to remove the tail lamps, unplug the electrical plugs for the lamps, install a jumper connection on each side of the car, and then run the harness behind Select Your Vehicle--Select Year--20172016201520142013201220112010200920082007200620052004200320022001200019991998199719961995199419931992199119901989198819871986198519841983198219811980197919781977197619751974197319721971197019691968196719661965196419631962196119601959195819571956195519541953195219511950194919481947194619451944194319421941194019391938193719361935193419331932193119301929192819271926192519241923192219211920191919181917199 TowingSports & RecreationTrailerVehicleRV & CamperManufacturersHelp InfoTowingSports & RecreationTrailerVehicleRV & CamperManufacturersHelp Info Free Shipping on Orders Over $50Only 1 Hours54 Minutes Remaining Troubleshooting Right Side Turn Signal Not have a peek here

Make sure the connection point is free of rust and corrosion as that could cause a bad ground.The driver side light should have a yellow and brown wire connected. When I swap the green and yellow wires at the connector, the problem moves to the other side of the trailer. Thanks for the suggestions and advice given here. So now heres my problem. https://www.etrailer.com/question-25308.html

Trailer Lights Work But No Turn Signal

etrailer.com 99,852 views 5:25 This Old Trailer: Troubleshooting the Ground Wire - etrailer.com - Duration: 3:31. Bill Eaglerunner 35,225 views 3:03 How to Test and Wire Trailer Lights Using a Hopkins 4 Flat Connector Set - DIY Chevy GMC - Duration: 6:05. Choose your language. Loading...

Worked fine for years before this. If so clean them out or replace the connectors with new ones.If the problem is not found in the connectors, you will need to follow the trailer wiring and check all My blinkers are not running fast when I connect to the trailer. Trailer Turn Signal Not Working When Lights Are On I always run wired grounds to each device when I wire a trailer.

click here.Products Referenced in This QuestionQuickee Circuit Tester 5 reviewsCode: 3808Retail:$34.41Price:$23.95WiringTools for WiringTestersCircuit TesterDraw-Titemore information > Product Page this Question was Asked FromPeterson Square Trailer Tail Light, 6-Function, Right Hand 93 Sign in to make your opinion count. Vic Clemmons, NC Shop By Vehicle Car Wagon SUV/Jeep Minivan Truck RV/Camper Shop Popular Brands Order Information Order Tracking Shipping Information Lowest Price Pledge Privacy Policy Your Account Login Customer Service https://www.etrailer.com/question-31328.html Close Learn more You're viewing YouTube in English (UK).

I've spent a lot of time to get this far. Trailer Blinkers Dont Work When Lights Are On I think by swapping the left (yellow) and right (green) wires at the truck and seeing the problem switch sides on the trailer, it points at the truck. When the weather dried, I had completely different behavior. If it tests good still look for nicks that could short it out by touching the trailer. 4.

Left Turn Signal On My Trailer Not Working

I then redid the ground on the truck's converter box, and then my light testing of the truck's plug was consistent with what I saw on the trailer - nothing from Good Luck. Trailer Lights Work But No Turn Signal Thankfully I was given one by someone who sold their van. Trailer Brake Lights Dont Work I am including a link to a troubleshooting video that should help you with locating the problem on your trailer.expert reply by: Jeff D
Ask your question or add a comment to

If you have an import or vehicle with yellow turn signals, then you probably have a trailer module wired in also which would need to be checked. http://techese.net/turn-signal/turn-blinker-not-working.html So if the brake light is working then the turn signal should be too. No trailer lights will work properly without this pricey harness. And don't forget to check the ground at the last fixture... Trailer Brake Lights And Turn Signals Not Working

The turn signal not working makes sense because with the brake lights, there is a constant signal coming through which is enough to make the lights illuminate on both sides like Close X View Mobile Site Remind me later Review A privacy reminder from YouTube, a Google company Skip navigation GBSign in Loading... If the bulb is known good (swapped, ohmed out OK), and you're getting voltage at the bulb connector, then it's probably corrosion at the connector preventing continuity. http://techese.net/turn-signal/trailer-brake-lights-and-turn-signals-not-working.html You can change this preference below.

In either case, the ground will need to be attached to a clean and corrosion free bare metal surface.You can also make sure that the main ground from the trailer connector Trailer Turn Signals Not Working When Headlights Are On Almost did that last weekend, 'til I remembered that I had a spare bulb in the truck (Last trailer had LED lights for a couple of years. Someone mentioned fuses.

The main connector grounds should be attached to clean and corrosion free bare metal surfaces.The light grounds should also be attached to clean and corrosion free bare metal surfaces.

You may have one under the dash and one other the hood. Everything else - both running lights, right brake, right signal, works. The green wire is right turn and brake light.I am including a link to a FAQ page on trailer wiring which will describe how to troubleshoot your trailer wiring.expert reply by: Why Wont My Trailer Turn Signals Work Reply With Quote Jun. 28, 2014,07:27 PM #2 Guin View Profile View Forum Posts Private Message Schoolmaster Join Date Sep. 5, 2005 Location Mass.

If so, correcting the bad ground or broken wire could solve the problem. Did the fuse fix your problem? If it still doesn't work, check your vehicle fuse box. this contact form I looked further and it seems as though the middle lead looks broken at the bottom where I guess it would return to ground for the directional.

Thanks...asked by: John
Expert Reply:You will first want to check the fuses on your tow vehicle. trace the turn signal wire from the lamp to the tailer plug and look for worn, nicked or ratty looking sections in the wire.....or easier put an ohm meter on it Do you have an impulse from the truck at the harness????? Register All Albums FAQ Community Wikiposts Calendar Today's Posts Search Search Show all Wiki Recent Changes Community Links Pictures & Albums Members List Search Forums Show Threads Show Posts Advanced