Home > Trim Gauge > Trim Gauge Not Working

Trim Gauge Not Working

Contents

Sign in 6 Loading... Suzuki 4-stroke 2002 is white with yellow tracers) to gauge sender terminal, and black to ground. Newtauk1 posted 05-22-2009 08:35 AM ET (US) jimh,Thanks for the info regarding oxides of silver and copper. The other wire should go to ground (with an ohm meter, zero ohms to ground). have a peek here

Have no other wires connected to the gauge. Make sure your engine has a trim sender. Wood, Foam, Starboard Wood Core Materials and Foam StarBoard Plastic Supplies Reinforcing Boards Boating Supplies Marine Supplies Rope and Running Rigging Ventilation Oars, Oarlocks and Paddles Cooking and Galley Supplies Swim Posts 1,392 Is It The Gauge Or Sender????

Trim Gauge Not Working Volvo Penta

I can replace the gauge easy enough but can't get at the sender unit with the boat in the water.............Don't know where to start.... [img]/forums/images/graemlins/blush.gif[/img] Regards, Paul. On top of each solenoid, the large BLUE wire from the pump motor attaches to a large copper stud with the solenoid that has the small blue wire at the base Dear forum users, Due to legal restrictions in the ongoing Cheeki Rafiki trial, we have had to momentarily remove all comments regarding the case. Safety Flotation Safety 3M Respirators Fire Safety Equipment Gloves EPIRBs and Personal Alarms More Safety...

They are mounted on either side of the Gimbal Ring. Most OEM service manuals are written with the assumption that the service technician understands nothing about electricity, and they provide procedures that assume very little knowledge on the part of the If the gauge reacts this way, any remaining problems will be in the sender or connecting wiring.

Related Products Faria Chesapeake Series Gauges Faria Coral Series Gauges Faria Dress White Boat Trim Gauge Wiring Diagram I was in your shoes last season and even spent a day on the water running with one engine stuck tilted up.

I do not think there are universal values for these components in the circuit. To start viewing messages, select the forum that you want to visit from the selection below. Paint Supplies Brushes Paint Rollers Paint Pots Mixing Paint Strippers More Paint Supplies... navigate here in forum Mercury Mariner Outboard Archive Replies: 1 Last Post: 02-25-2007, 11:40 PM Posting Permissions You may not post new threads You may not post replies You may not post attachments

I am semi competent and can certainly follow a trouble shooting guide. Evinrude Trim Gauge Not Working All electrical functions work exept the tilt and trim gauge. Make sure your engine has a trim sender. They look simple to replace but to feed the cable through you have to remove the leg and gimble, so do it at the same time as your bellows.

Boat Trim Gauge Troubleshooting

The BLUE & GREEN wires bring 12 volts from the switches to the two solenoids on the pump assy. http://continuouswave.com/ubb/Forum6/HTML/002320.html The trim sender and limit switch have been working perfectly now for 8 years *touches wood*, hence my assertion that it is possible to rewire them. Trim Gauge Not Working Volvo Penta Working... Mercury Trim Gauge Not Working The trim/tilt switch is a 2-way switch and will show continuity only when it is toggled in each direction between two of the wires.

Sign in to add this video to a playlist. navigate here it would work better if you started a new topic under the REPAIRS/MOD section rather than jumping into another topic thread. Thats just what I was thinking..... If the distance is approx. 22 +/- 1/4 inches, then the trim limit switch is adjusted properly and the commander trim toggle switch is working in the up/down mode. How Does A Boat Trim Gauge Work

The OD trim limit switch will only send voltage to the trim/tilt switch in the upward toggle position if the OD limit switch is below the adjusted trim limit that keeps At the end of "Trim" range (point where trim speed increases), the pointer will be at the third graduation, balance of travel to full "Up" position will occur during "Tilt" range. Please accept our apologies for any inconvenience and thank you for your patience. Check This Out Tilt motor and see if it changes.

The Starboard switch is the Trim Level Sender switch. Mercury Outboard Trim Gauge Sending Unit All rights reserved. Smithsm posted 06-17-2009 09:06 AM ET (US) Well what do you know - the trim tab guage is working but is way out of calibration - meaning that

Replacement without taking the drive off is damn near impossible. 03-19-2008,12:31 PM #3 elgineddie View Profile View Forum Posts Private Message View Articles Contributing Memeber Join Date Mar 2007 Location St.

I got in to the hang of guessing the leg trim on the way back from Cowes.......Any tips on working out my leg trim with guess work?? Smithsm posted 05-21-2009 12:08 PM ET (US) [Can] I buy a CONDUCTIVE grease ? Register a new account Sign in Already have an account? Alpha 1 Trim Sender All about Zinc Anodes How do I check my carburetor?

Replace Your Alpha One Water Pump Replace your Alpha Gen II Water Pump Rebuild your Bravo Raw Water Pump Troubleshoot & Replace your Alpha Shift Cable Troubleshoot & Replace your Bravo At the point where trim speed increases, the pointer will be at the full "Up" position. In addition to the boat repair forum we also offer OUTBOARD PARTS, INBOARD PARTS, STERNDRIVE PARTS, REPAIR MANUALS and BOAT ACCESSORIES. this contact form Exhaust Manifolds...IMPORTANT Information How do I Winterize my engine?

I had a problem with mine and that fixed it right away. Share this post Link to post Share on other sites TreeTop Members 20 posts Location:Huntsville, Alabama Posted 9 Jul 2010 · Report post New guy here! Close Yeah, keep it Undo Close This video is unavailable. Important: if the studs on the either solenoid are dark and not like a clean penny, especially the BLUE wired solenoid, this solenoid is failing due to age and/or a loose

If it doesn't you need a new sending unit. Jessica Jae 574,403 views 12:39 Replace Mercruiser Transom Switches WITHOUT removing lower unit - Duration: 14:21. Forum Home New Posts Help Forum Actions Mark Forums Read Quick Links Today's Posts View Site Leaders Who's Online Today's Post Articles & Videos Popular Topics Search Forums Forum Home Gas Sterndrives.Com Change your Alpha Gear Lube Change your Bravo Gear Lube Why does my drive lube have white streaks?

Then fine adjust from there, based on conditions etc. Knowing I had issues I was careful the rest of the day to not trim up more then a bump or two. Old topics of a technical nature are like a library book, Please do not write in them. 2. Hardware Cleats Hatch Adjusters Hinges Handles, Pulls and Rings Deck Hardware More Hardware...

Reply With Quote 29-06-09,09:02 #5 ExcaliburII View Profile View Forum Posts Private Message Registered User Join Date Jun 2005 Location Gloucestershire Posts 210 Re: Is It The Gauge Or Sender???? Check the sending unit that is mounted inside the engine bracket, aft of the transom. I had the exact problem and it was stuck in the down position. Category Howto & Style License Standard YouTube License Show more Show less Loading...

Then measure the distance between the trim cylinder attaching bolts. Sign In Now Sign in to follow this Followers 4 Go To Topic Listing Boat Talk All Activity Home Chaparral Boats Forum Boat Talk Dashboard Trim Gauge Contact Us Community Software The blue wire gets 12 volts only when the toggle is held up or the trailer switch is pushed in. Below the silver is copper.

The sender usually has two wires - brown with white stripe (Yamaha is pink. What can I do to prevent this in the future?