Home > Trim Gauge > Trim Gauge Not Working Evinrude

Trim Gauge Not Working Evinrude

Contents

Share Share this post on Digg Twitter Share on Facebook Reddit! Is that what yours is doing? I will get the manual. boashna 48,759 views 6:10 Yamaha Trim Sender - Duration: 1:44. have a peek here

Close Yes, keep it Undo Close This video is unavailable. whenever i trimmed down it went up. to the toggle up/down and trailer up switches. when i manually move the sender it moves backwards.

Trim Sender Replacement

Next check the three (RED, BLUE & GREEN) wire connector at the pump assy. Am I looking at the right place? __________________At the moment Boatless! If the needle does not move sender is bad. __________________ Karry Kyllo Last edited by KPKyllo; 04-23-2014 at 04:07 PM.

great guys to deal with. I know the I-Command needs to be programmed via a laptop. If the distance is approx. 22 +/- 1/4 inches, then the trim limit switch is adjusted properly and the commander trim toggle switch is working in the up/down mode. Mercury Outboard Trim Sending Unit Change the solenoid.

The Gauge Sender is "Ayuh,... Evinrude Trim Gauge Wiring Diagram Storage / Organization Boat Shrink Wrapping Boat Stands and Blocks Tarps and Boat Covers Outdoor Shelters Tool Boxes More Storage / Organization... After I verified good ground at the gauge I started troubleshooting by disconnecting sending unit and checked resistance which was appx 1 ohm up / 100 ohms down, which I think news It could be that the sending unit is stuck in position due to corrosion or a foreign object.To check, light up the gauges (not the engine) and move the sending unit

Per Mercury, you can only tilt up past half way point if under "X-amount" of RPMs. Mercury Outboard Trim Sender Adjustment If the switch voltages are as they are supposed to be then go to the trim/tilt pump assy. Moss Motors, Ltd. 78,576 views 4:15 How To: Replacing the Powerpack on a Johnson / Evinrude Outboard Motor - Duration: 20:53. This plug can vibrate loose and cause your problem.

Evinrude Trim Gauge Wiring Diagram

Loading... http://www.marineengine.com/boat-forum/showthread.php?294335-Trim-gauge-not-working My Account | Wish List Checkout: 0($0.00) Item(s) in your cart: There are no items in your cart. Trim Sender Replacement I have only owned jet drives up to this point. Boat Trim Gauge Not Working The trim/tilt switch is a 2-way switch and will show continuity only when it is toggled in each direction between two of the wires.

I am semi competent and can certainly follow a trouble shooting guide. navigate here Other Teleflex trim gauges will damage the pre- 2001 Yamaha trim sender. TheDIYMechanic 3,177 views 12:23 How to Replace the Gauges in your boat - Duration: 14:00. Comment Cancel Post Previous Next iboats Boating Forum Directory Over 100,000 Questions & Answers Outboard Motor Topics Mercury Outboards Johnson Outboards Evinrude Outboards Force Outboards Yamaha Outboards Mariner Outboards Suzuki Outboards Evinrude Trim Sending Unit

Trailer Parts Trailer Boat Guides and Pads Trailer Winches and Jacks Trailer Rollers Trailer Hubs and Axles Trailer Lighting More Trailer Parts... On top of each solenoid, the large BLUE wire from the pump motor attaches to a large copper stud with the solenoid that has the small blue wire at the base View Member Profile Find Member's Topics Find Member's Posts rojorin Gold Level Member 3-2010 Registered:1208606051Posts: 234 Posted 1251247824 Reply with quote #8 Any suggestions?? __________________At the moment Boatless! Check This Out Fasteners Fasteners Screws / Bolts Nails, Tacks, Brads and Escutcheon Pins Nuts Washers Rod More Fasteners...

Previous Topic | Next Topic Print Tweet Reply × Insert Photos Web address (URL) Image URL If your URL is correct, you'll see an image preview here. Trim Gauge Not Working Mercury For the best results, please start a new topic. Smithsm posted 05-21-2009 12:03 PM ET (US) JimH--[Thanks] again.

Begin a new thread to change the topic.

A small RED wire attached to the bar stud sends 12 volts to the switches which in turn sends the 12 volts to the solenoids which turns on the pump motor. Do not take over someone else’s topic (aka hijack) with your own question, even if it is similar. The RED wire in the plug sends 12 volts from the pump assy. Yamaha Outboard Trim Sender They go bad also.

But electrical motors with brushes can often be cajoled into working again with a little jolt, especially low-voltage motors like a 12-VDC motor. Contact Us Advertise Bass Fishing Forum - Austin Bass Fishing Archive Privacy Statement Terms of Service Back to top All times are GMT -6. Does that make sense? http://techese.net/trim-gauge/trim-gauge-not-working.html You don't want to remove the silver plating with a wire brush to end up with the copper exposed.If terminals are dirty or badly corroded you should clean them as much

Working... The stop is on top of the sender arm when the motor id trimed all the way up, is thatcorrect? Ohmmeter needle should move up as the outboard is trimmed up. Close X View Mobile Site Go Go Go Go Order (800) 209-9624 Phone Orders (800) 209-9624 $7.95 Flat Rate Shipping Menu Boat Engine Parts All Engine Brands — All Engine Parts

Abrasives Discs Rolls and Longboard Abrasives Festool Abrasives Fein Abrasives Sheets More Abrasives... jimh posted 05-19-2009 02:12 PM ET (US) I believe the motor is tilting, just the gauge isn't reading. and make sure the purple wire connector (single wire) and the blue wire connector with two blue wires on one side of the connection are not corroded or loose. Sure -- likely a wrong sender.

Clean out the old grease and pump fresh Mercruiser 2-4-C grease thru the zerk fittings before reinstallation.