Home > Touch Lamp > Touch Table Lamp Not Working

Touch Table Lamp Not Working

Contents

To fix this problem I clip the wire connector from the wire and strip the wire about 1/2 inch. It may have the heat-sink tab soldered too, and you may have to apply more heat for that to part.If it is screwed down with a small screw, and a mica price is only 6.5gbp. House is less than three years old, and is considered a high end house and has no electrical issues. http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html

You may need to wiggle the sleeve as you pull, so it releases from the base. 9Check the lamp wires to ensure they connect to the two terminal screws on the The bulb does seem to flicker very slightly but it does work. As usual it took 8 months and 10 minutes to fix. Some fuses look like lamps - replace only with an identical fuse - not with a lamp! 7.13) Comments on Christmas tree bulb/string repair Original type of problem: No light but

Touch Lamp Won't Turn Off

glenn said, February 16, 2012 at 2:52 pm (Learned something new!) can someone give me specs on the thrysters or some kind of an identifier so i can call around to Yes No Voted Undo Score 2 Cancel Comments: Awesome, thanks for the info! 04/26/2010 by Ben Eisenman Add a comment 0/1024 Cancel Post comment Are you sure you want to delete The first problem is getting into the base, to take the box apart. My lamp was missing one blub.

Electronic parts all have acceptable ranges of operation and when put into identical circuits they sometimes perform differently. Paul Manion 1,447 views 6:56 Делаем лампу с сенсором прикосновения DIY Light Touch/Inductive Switch for Lamp Review ET0802193E - Duration: 5:29. ANY HELP OUT THERE? Touch Lamp Stays On But these lamps wont work in outlet in B/Room, or Kitchen, or Living room… WHAT do I change for that? (It really does it's thing correctly in some of my homes'

Touch switch that came with new cabinet behaves exactly the same. The wires marked A and B (sometimes called 'travelers') may be in a single (Romex) cable and should be on the screws that are both the same color. Much handier than a new lamp or dimmer boxes Virginia B Yocham said, October 24, 2016 at 4:44 am (Knew it already.) Just an fyi- they also make a touch light http://homeguides.sfgate.com/reset-touch-lamp-40423.html I'm blonde, so that doesn't help lol.

You will get news, coupon codes, and email! Touch Lamp Control Module Transcript The interactive transcript could not be loaded. you just plug the adapter into the wall and the lamp into the adapter. The ring terminal connects to the nipple with a locknut.

Touch Lamp Not Working After Blown Bulb

Secure the ring terminal to the nipple, using the locknut you previously removed. 8Match the black wire connected to the touch-control box with the taped lamp wire from the plug. Rating is available when the video has been rented. Touch Lamp Won't Turn Off essortment 221,625 views 3:23 Lamp Repair - Duration: 9:37. Touch Lamp Sensor Touch-sensitive lamps almost always use a fourth property of the human body -- its capacitance.

Was this answer helpful? http://techese.net/touch-lamp/touch-light-lamp-not-working.html Loading... At the moment the only way to turn on the lamp is by physically touching it somewhere after power is connected to it. The switch has come loose from its glue on the bottom. How To Repair A Touch Sensitive Lamp

Just Choke off the sense wire with the resistor and 2.5 mH choke. A compact fluorescent light (CFL) or LED (light-emitting diode) bulb only works in touch lamps if it is labeled as dimmable. 5Unplug the touch lamp and remove the light bulb if However, this dimmer also includes a choke (L1) and capacitor (C2) to suppress Radio Frequency Interference (RFI). have a peek here WARNING: Do not be tempted to bypass a bad bulb with a wire.

The Better Homes and Garden website also provides a listing of retailers that sell sta... Touch Lamp Control Switch Erratic problems could be due to bad connections, dried up electrolytic capacitors (especially if the electronics module is near the hot bulb), or even external E/M interference (e.g., a dimmer or Log in to Reply Leave A Reply Cancel ReplyYou must be logged in to post a comment.

Light Fixtures and Your Decor Wooden Bridge Arm Socket Interior Replacement Floor Lamp with Busted Socket Cluster and Pull Cha... ► July 2014 (10) ► August 2014 (9) ► September 2014

Joan said, January 29, 2010 at 3:40 pm (Learned something new!) After reading Carolyn's problem there is no way I will take the lamp apart. Sign in Share More Report Need to report the video? there's too many combinations to use so the colors won't mean anything. Touch Lamp Wiring Diagram A short in the touch switch could cause it to never come on.

Many elevators therefore use buttons that are sensitive to the warmth of the human finger. I believe these have been replaced by the F and G suffix devices, where the F has a 25mA gate current for a fully ON state. With some, a dimmer can be installed at only one switch location. http://techese.net/touch-lamp/touch-lamp-not-working.html Then divide the 'bad' portion in half and test one half of it and so forth.