Home > Touch Lamp > Touch Sensor Lamp Not Working

Touch Sensor Lamp Not Working

Contents

Paul said, January 16, 2012 at 4:47 pm (Learned something new!) We've had three of these lamps. Triode, Tetrode and Pentode variations of the thyratron have been manufactured in the past, though most are of the triode design. Two of the 3-way type will be needed at the ends of the circuit (below) with 1 or more 4-way type in between. One slight tug of a wire, can break it, and the entire set goes dead. http://techese.net/touch-lamp/touch-lamp-sensor-not-working.html

Sign in Transcript Statistics 109,577 views 148 Like this video? Furniture store actually replaced the entire cabinet. Unplug the lamp and remove the bottom from the lamp base to expose the touch control. OK Lighting is the largest seller of touch lamps in the U.S. http://homeguides.sfgate.com/troubleshoot-touch-lamp-51907.html

Touch Lamp Not Working After Blown Bulb

With each touch, the brightness of the light bulb increases until the final touch turns off the lamp. They probably make them somewhere but the cost probably makes the swap pointless. Wrap a small piece of red electrical tape around the lamp wire connected to the touch control’s red or gray wire. David Norris 7,752 views 17:08 Lamp Dimmer Switch - Touch Lamp Control - Duration: 1:32.

Then remove the wires from the switches. Unlike table lamps where most of the heat rises from the bulb away from the socket, mounting the sockets horizontally or inverted (base up) can result in substantial heating and eventual Certainly those two parts (fusible resistor & TRIAC) are easy to replace, and if the fusible resistor protects the control IC CHIP that is a good benefit, as they are hard Touch Lamp Turns On By Itself Really pretty as ornaments even though they don't work, so decided not to throw them away.

I was in tears laughing because I was in the same boat as almost everybody here!! Our pair of lamps are 4 years old and, despite bulb changes, this has never happened before! Wrap a small piece of black electrical tape around the lamp’s wire connected to the black touch control wire. 12Remove the three wire connectors holding the lamp wires together with the http://homeguides.sfgate.com/reset-touch-lamp-40423.html for details.

into the bin. Touch Lamp Control Switch Plug the touch lamp into an outlet. Full Answer To determine the source of the problem, try troubleshooting common issues that may cause the lamp to work improperly.The lamp will not turn onIf the lamp will not turn Same thing happened.

Touch Lamp Sensor

A: The most common reasons for a blown light bulb include either cheap bulbs, loose connections in the lamp holder, a loose spring loaded connection in the bu... you just plug the adapter into the wall and the lamp into the adapter. Touch Lamp Not Working After Blown Bulb When I opened the dimmer module, there was a small black mark on the resistor indicating overheating and my meter showed it was open circuit. Touch Lamp Stays On within an hour would not turn off.

This is rather late info as all the people reading these posts (me included) all ended here after the burnout :) However it will prevent a future problem on a future http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html My son works the CB. My wife could never get our lamps to switch, she often had to blow on her hand first to get it moist so it would make better contact. Q: Where can I find table lamps? How To Repair A Touch Sensitive Lamp

After all, you can get them typically around 5-10 bucks a set. They also use a cheap method of crimping the wiring together in these lights. Guess what? http://techese.net/touch-lamp/touch-lamp-not-working.html There will be a single Hot - that goes on the common of the 3-way switch.

I changed the bulb & after a very few seconds the bulb was so hot I thought it to be dangerous.Was it & what would have happened if I had left Touch Lamp Control Module This works up to a point, until more than 4-5 bulbs blow out at once, then the remaining ones get too much voltage and blow out too. I learned something new!

Mark Novaky said, December 15, 2009 at 2:12 pm (Learned something new!) I have owned LITERALLY 4-5 touch lamps and this bulb failure causing lamp failure has happened on EVERY SINGLE

This is, (duh!) the 'common' terminal. If the lamp is stuck off, there could be a bad connection or bad bulb, or the electronics module is defective. Vitalii Tereshchuk 17,870 views 5:29 i - How To - D I Y - Fix a Touch Lamp (don't use fluorescent) - Duration: 1:56. Touch Lamp Wiring Diagram I will probably replace the whole box as soon as I figure out where to get a deal.

If your touch lamp is stuck permanently ON, or will not switch on, then the power control transistor (called a THYRISTOR, or TRIAC), is shorted, or open circuit (blown).What usually happens David Long 1,267 views 0:51 Loading more suggestions... Also if a touch lamp gets knocked over many times it will blow the sensor. Check This Out Working...

Loading... Look inside the socket for a small brass tab. They simply replace the existing switch. Two parts: 1/4 watt, 1k Ohm resistor and 2.5 mH 1/2 watt size molded coil.

I know they can't be used with a dimmer switch, and I believe the touch sensitive lamps will also fail if they try to force the bulb to different levels of This one uses a toggle style potentiometer where the up and down positions operate the switches. It is very easy to do and you don't even have to solder. Any ideas on how to fix it?

It's too much trouble to fuss with the touch lamp which was really cheap in the first place anyway. We tried putting heavy aluminum foil under the router. Replace a light bulb, plug the touch lamp into the outlet and check its function. Erika said, March 3, 2010 at 10:46 pm (Learned something new!) Thanks so much for posting this!

ROY R. I was ready to throw out my mom's lamp until I came across this. If more than one bulb is burnt out, this may further complicate matters. The Home Depot 564,424 views 6:04 Home Help : How to Replace a Lamp Socket - Duration: 3:23.

Was this answer helpful? Pages About November 2016 S M T W T F S « Oct 12345 6789101112 13141516171819 20212223242526 27282930 Categories Select Category Animals(13) Art(4) Astronomy(25) Bicycles(1) Biology(20) Books(48) Chemistry(5) After much wasted time trouble shooting, in desperation (and without much hope) I tried a well known branded bulb replacement and - bingo- light now works again perfectly.