Home > Touch Lamp > Touch Sensitive Lamp Not Working

Touch Sensitive Lamp Not Working

Contents

Plug the touch lamp into an outlet. My new part also had a yellow wire and my lamp had a green on so I attached those two together. Q: How do you wire a security light? Tony Davis said, May 1, 2012 at 4:53 pm (Knew it already.) Hi, I am glad that all of you reading this blog, have got something from MY original article on Source

Any experts out there to help with this. David Long 1,267 views 0:51 Loading more suggestions... Every once in a while the lamps come on by themselves for no apparent reason. so now the brand new (to me) lamp can't be turned off cuz I wrecked the sensor with the CFL. http://homeguides.sfgate.com/troubleshoot-touch-lamp-51907.html

Touch Lamp Not Working After Blown Bulb

NEWSLETTERS Get the best of HowStuffWorks by email. The base can be stuck back with a glue-gun. I didn't really think I would find an answer to the problem online but decided to give it a shot.

Virginia B Yocham said, October 24, 2016 at 4:42 am (Knew it already.) Just an fyi- they also make a touch light socket that turns any lamp I to a toch Wrap a small piece of black electrical tape around the lamp’s wire connected to the black touch control wire. 12Remove the three wire connectors holding the lamp wires together with the glenn said, February 16, 2012 at 2:52 pm (Learned something new!) can someone give me specs on the thrysters or some kind of an identifier so i can call around to Touch Lamp Control Switch Should you care, these implement the multiple input XOR (exclusive OR) logic function for controlling electrical devices.

But now I know for when I do have a more expensive lamp! Touch Lamp Sensor Here is one way to identify the proper wires more quickly than trial and error: 1. However, what I learnt was that the internet continues to be so useful in so many different ways, providing access to solutions for diverse problems. http://homeguides.sfgate.com/troubleshoot-touch-lamp-51907.html I ended up removing mine - an electrical storm wiped one out and wiped the other out a few years later. 7.9) Touch lamps and RF interference While many people swear

I changed the bulb & after a very few seconds the bulb was so hot I thought it to be dangerous.Was it & what would have happened if I had left Touch Lamp Control Module One circuit might need a good hard touch while the other might need only a slight touch. Incandescents are so last century. But anyway, the unfortunate upshot is that the lamp is now non-touch-sensitive.

Touch Lamp Sensor

Replaced it with an old fashioned bulb & still nothing. Some fuses look like lamps - replace only with an identical fuse - not with a lamp! 7.13) Comments on Christmas tree bulb/string repair Original type of problem: No light but Touch Lamp Not Working After Blown Bulb Erika said, March 3, 2010 at 10:46 pm (Learned something new!) Thanks so much for posting this! Touch Lamp Stays On Connect the lone screw (the different or darker colored one) on one switch to this Hot wire.

GrandadIsAnOldMan 45,706 views 9:35 Touch lamp sensor fitment guide Rike RK-01 - Duration: 6:56. this contact form Stumbled across your blog when I was searching on how to repair my broken touch lamp….all the information I needed in one place (thank you!) Able to find triacs on eBay Paul said, January 16, 2012 at 4:47 pm (Learned something new!) We've had three of these lamps. You have several options: * It may be obvious from the way the box is wired as to which are the A/B pair. * Use a tester to figure out which Touch Lamp Turns On By Itself

I knew all this, and still did not do it, despite the fact that I own a room full of electronics and have dozens of these strips that I could have Mine went out after about 10 years of use and it survived maybe three bulb changes. I know they can't be used with a dimmer switch, and I believe the touch sensitive lamps will also fail if they try to force the bulb to different levels of http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html Or did, that is.

Thanks for the info and for the clearly worded post. Touch Lamp Wiring Diagram MACA said, September 11, 2010 at 5:40 pm (Knew it already.) I stumbled over this list of postings while trying to find again, the place that was selling replacement dimmers for does this mean i either toss the whole thing or fix it as you have all explained ? ( thats not going to happen )…..

My light came on & would not go off after he put his light off.

It's been soo good to me and my children for so long now!!! Now, to see if I can go get this part from a supply house, as I am to impatient to wait ! Sometimes will stay off for a while, and then turns itself back on. Touch Lamp Sensor Wiring Diagram Good luck to us all, P.S.

And track its usage so I can estimate when the bulb is about to die and swap it before the cataclysmic "bright flash" kills that lamp, too. Two of the 3-way type will be needed at the ends of the circuit (below) with 1 or more 4-way type in between. Thank you so much for this! http://techese.net/touch-lamp/touch-lamp-not-working.html Again, it makes no difference which goes where.

If you do use Romex with a black and white wire, put black tape on the insulation at the ends of the white wire (or paint the ends black) to indicate Erratic problems could be due to bad connections, dried up electrolytic capacitors (especially if the electronics module is near the hot bulb), or even external E/M interference (e.g., a dimmer or