Home > Touch Lamp > Touch On-off Lamp Not Working

Touch On-off Lamp Not Working

Contents

Maybe you could go with a touch-sensitive lamp with a compact fluorescent bulb. Thinking that it was faulty, i went back to the store and got a replacement. does this mean i either toss the whole thing or fix it as you have all explained ? ( thats not going to happen )….. cka mark otho keen 9,139 views 1:56 How to Make a Simple Touch Sensor, Tutorial and Circuit - Duration: 15:16. http://techese.net/touch-lamp/touch-lamp-not-working.html

In the other position, the connections are interchanged. The bad one I will take to a lamp repair place and if it's not too expensive I'll get it fixed. Yes No Voted Undo Score 1 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Now I know this is dumb but...

Touch Lamp Not Working After Blown Bulb

Unplug the lamp and remove the bottom from the lamp base to expose the touch control. A: Quick Answer If a touch lamp is not working properly, troubleshoot the issue and determine if it is a simple fix or if there is a short or defect with Take off the lampshade to access the lamp harp. Connect the same-color screws on the switch to the other two wires.

dadpad wrote:Do things logically and slowly Ok thanks dadpad wrote:I'm willing to bet its a voltage drop type thing applicable to that one power outlet which means a short and possible I found the ¾ Watt was twice the size of the blown part and the ¼ Watt was 2/3 the size. This of course is my exact problem. Touch Lamp Control Module There are Fluorescent bulbs that dim and also dimmers for these also.

Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. How To Repair A Touch Sensitive Lamp Kevin said, April 25, 2010 at 4:42 pm (Learned something new!) I was not aware touch sensors do not work well with fluorescent lights because of the variable power. I was ready to throw out my mom's lamp until I came across this. original site After much wasted time trouble shooting, in desperation (and without much hope) I tried a well known branded bulb replacement and - bingo- light now works again perfectly.

You just delighted my nine year old twin boys and me. Touch Lamp Wiring Diagram i found a repair part on ebay for $7.50 with free shipping, you can probably find similar ones also. matthew said, July 17, 2010 at 2:11 am (Knew it already.) I have a touch lamp which I wish to be able to turn on automatically on a wall switch. Quality control is not an issue when they build xmas lights.

How To Repair A Touch Sensitive Lamp

WARNING: Do not be tempted to bypass a bad bulb with a wire. http://www.wkiri.com/today/?p=49 Today I bought a dimmable compact flourescent but it also didn't dim. Touch Lamp Not Working After Blown Bulb GrandadIsAnOldMan 45,706 views 9:35 Touch lamp sensor fitment guide Rike RK-01 - Duration: 6:56. Touch Lamp Stays On Additional information below kindly supplied by BW of BEDS (about yet another variation of touch-lamp circuits, where a fusible resistor is used to protect the circuit): “This specific touch lamp had

And track its usage so I can estimate when the bulb is about to die and swap it before the cataclysmic "bright flash" kills that lamp, too. http://techese.net/touch-lamp/touch-lamp-sensor-not-working.html dadpad wrote:Now I know this is dumb but... within an hour would not turn off. In most cases the ground is connected directly to the neutral at the breaker box. Touch Lamp Sensor

I came across this site looking for just such an explanation. I guess I will have to learn to replace the thyristors. there's too many combinations to use so the colors won't mean anything. have a peek here Dimmers are under the most stress and generate the most heat when operating at about 50% output.

Joan said, January 29, 2010 at 3:40 pm (Learned something new!) After reading Carolyn's problem there is no way I will take the lamp apart. Touch Lamp Control Switch Now, turn off the power and confirm that it is off by retesting the hot wire you identified above. 2. jen said, October 23, 2007 at 8:32 pm (Learned something new!) Definitely learned something new!

Sign in Transcript Statistics 109,577 views 148 Like this video?

Things You Will Need Screwdriver Tape Pliers Replacement touch-control box References (1) The How-To Book of Repairing, Rewiring, and Restoring Lamps and Lighting Fixtures ; Rachel Martens About the Author Cecilia You've got one wire left,,, that's the other common. Soooo.. Touch Lamp Turns On By Itself Sign in 149 47 Don't like this video?

You will find one screw different from the other two. The red or gray wire connects to one of the lamp wires that threads through the lamp body and connects to the socket. 5Untwist the connectors that hold the lamp wires Thanks to those who share their expertise freely. http://techese.net/touch-lamp/touch-floor-lamp-not-working.html There were no markings for the power rating.

Squeeze the sides of the harp together and insert them in the harp saddle. Plug the touch lamp into an outlet. Suggestions besides just getting rid of the touch lighting (which I may do) or getting rid of the cabinet (which we like very much)? GuruBrew 159,253 views 18:08 How To Replace a 3 Way Lamp Switch - Duration: 7:39.

These use a MOSFET type circuit to switch the lamps on and off. Q: What is the importance of light in our life? Go to the hardware store and buy a tester - they cost about $5 US. I have noticed some people posting problems with Fluorescent bulbs not dimming.

Use your fingers, needle-nose pliers or a small flat-head screwdriver to lift the tab slightly. Guess what? Kayte said, June 28, 2009 at 6:52 pm (Learned something new!) My own touch lamp just blew up. The little bulbs were also designed, that if the filament breaks in the bulb a piece of foil inside it shorts out that bulb so that the remaining lights keep on