Home > Touch Lamp > Touch Light Lamp Not Working

Touch Light Lamp Not Working

Contents

I Was looking forward to this day. in »Home Repair IC Light Fixture too hot to touch in »Home Repair Which lube for lamp sockets? Unscrew the finial and lift the lamp shade off the lamp harp. 7Find the metal sleeves at the bottom of the harp on each side of the socket. For example, if you are using four 100 W bulbs, a 600 W dimmer should be the minimum choice and one rated at 1000 W would be better. Source

You'll be fine. 7.10) Incandescent fixtures A fixture is normally permanently mounted to a wall or ceiling. Up next Let's disassemble a touch sensitive "Touch Me" table lamp - Duration: 9:35. These are actually SPDT (Single Pole Double Throw) switches which look like ordinary wall switches but have 3 screws instead of 2. I don't understand why the brand of bulb should affect the performance - any offers?? http://homeguides.sfgate.com/troubleshoot-touch-lamp-51907.html

Touch Lamp Not Working After Blown Bulb

This works up to a point, until more than 4-5 bulbs blow out at once, then the remaining ones get too much voltage and blow out too. The peak current of that device is 140 AMPS! In more detail: First, shut off the power to the circuit. This one uses a toggle style potentiometer where the up and down positions operate the switches.

Every once in a while the lamps come on by themselves for no apparent reason. Resetting the touch lamp requires replacing the touch-control box. 1Remove the finial holding the shade onto your touch lamp. The part costs about $14 (you can probably find it cheaper, I got mine at a specialty lamp store) and you just take out the old one, keeping up with which Touch Lamp Turns On By Itself Common problems relate to this type of problem - bad connections or brittle wire insulation.

A touch lamp has a touch-control box installed inside the body of the lamp. Touch Lamp Sensor David said, March 15, 2010 at 2:30 pm (Learned something new!) Thanks! One slight tug of a wire, can break it, and the entire set goes dead. Flip the first switch, and another will be hot.

Your explanation was clear and comprehensive, so I almost felt I could change my thyristor. Touch Lamp Control Switch Again, replacement is straightforward. First I assume you wiggled all the bulbs, often just a loose bulb causes this. Paulette said, March 18, 2011 at 5:17 pm (Learned something new!) Thanks so much for the information.

Touch Lamp Sensor

There will be one or more sockets for light bulbs - often all wired in parallel so that all the bulbs come on at the same time. read this post here Wikipedia to the rescue: A thyratron is a type of gas filled tube used as a high energy electrical switch. Touch Lamp Not Working After Blown Bulb Wear safety goggles to protect against flying bits of glass. How To Repair A Touch Sensitive Lamp for details.

She attended Tarrant County College and studied English composition. this contact form I send 2 or more watts from my rig. When apart, locate the largest component on the board, with a metal tab with a hole in it. You will probably have no reliable way of telling them apart without testing or disassembly. Touch Lamp Stays On

Much handier than a new lamp or dimmer boxes Virginia B Yocham said, October 24, 2016 at 4:47 am (Learned something new!) Sorry- hit post twice Patti Allen said, October 30, Harsch received her Certified Nurses Assistant license in 2004. Twist the locknut counterclockwise and remove it from the nipple, using a pair of pliers. http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html All the other switches should be conventional 3-way or 4-way types.

Connect the same-color screws on the switch to the other two wires. Touch Lamp Control Module Sign in Transcript Statistics 109,577 views 148 Like this video? Mark Novaky said, December 15, 2009 at 2:12 pm (Learned something new!) I have owned LITERALLY 4-5 touch lamps and this bulb failure causing lamp failure has happened on EVERY SINGLE

Thanks to those who share their expertise freely.

I've ordered two transistors on Ebay (one for spare) and will be borrowing hubby's soldering iron to make the repair :-) Chris said, November 27, 2011 at 2:58 am (Learned something The ring terminal connects to the nipple with a locknut. Use the locknut you removed previously to secure it to the lamp. 15Reconnect the two neutral lamp wires to the new the touch control white wire using the wire connector you Touch Lamp Wiring Diagram Connect in-line with the touch wire.

Those of you who are able to obtain the energy C rated lamps (e.g. I learned something new! I believe these have been replaced by the F and G suffix devices, where the F has a 25mA gate current for a fully ON state. http://techese.net/touch-lamp/touch-lamp-not-working.html ExcelDriveVideo 86,535 views 7:39 Installing / Replace A Three Way Dimmer Switch - Duration: 6:39.

Alan Chatham 67,656 views 2:15 Home Help : How to Replace a Lamp Socket - Duration: 3:23. Q: Where can you purchase Scentsy replacement bulbs? You may need to spread the sides with a small screwdriver to defeat the plastic clips holding the two halves together. S1 is part of the control assembly which includes R1.

However, aside from not usually having a plug - being directly wired - they are similar to table lamps in what is inside. You don't need to be an electrician to do this. They are either black, red, white and yellow, or they are black, gray, white and yellow, depending on the manufacturer. 4Wrap a piece of tape around the lamp wire that connects Wrap a small piece of black electrical tape around the lamp’s wire connected to the black touch control wire. 12Remove the three wire connectors holding the lamp wires together with the

there's too many combinations to use so the colors won't mean anything. With some, a dimmer can be installed at only one switch location. My lamp won't dim after I changed the bulb and now the only way to turn it off is to unplug it. Wrap a small piece of red electrical tape around the lamp wire connected to the touch control’s red or gray wire.

Trina said, August 7, 2010 at 2:01 pm (Learned something new!) Hmmm, I just bought this lamp yesterday and have a CFL in it. When that happens I guess it will be time to get new lamps. As usual it took 8 months and 10 minutes to fix. When this happens, the touch lamp will remain in the "On" or "Off" position.

The wiring would be as follows: Location 1 Location 2 3-way Dimmer A 3-way Dimmer +---------+ /o----------------------o\ | Lamp | Hot o------o/ Silver 1 Silver 2 \o------| or |-----o Neutral Brass Plug the touch lamp into an outlet. SFGate Home Guides by Demand Media News Sports Business A&E Food Living Travel Columns More Less Cars Jobs Real Estate Find&Save Skip to main content. It is rather weird that this blog gets a higher ranking in Google than my original article on this, going back to around 2005.

Any idea why I might have the flicker? Check the lamp’s operation. thanks uri said, March 22, 2012 at 9:30 am (Learned something new!) Great stuff.