Home > Touch Lamp > Touch Light Control Not Working

Touch Light Control Not Working

Contents

Switch the other switch, and you'll find another hot. pulled the plug so no live juice. The wiring would be as follows: Location 1 Location 2 3-way Dimmer A 3-way Dimmer +---------+ /o----------------------o\ | Lamp | Hot o------o/ Silver 1 Silver 2 \o------| or |-----o Neutral Brass jim said, September 15, 2007 at 7:37 am (Learned something new!) Have you taken the lamp apart to see if you could replace the thyristor? (The part should be about less Source

Justin Hulbert 51,868 views 10:24 How to Update a Light Fixture - The Home Depot - Duration: 6:04. I have only known the little IC (chip) or diode get damaged once (see other pictures below), it is nearly always the THYRISTOR/TRIAC. Loading... A compact fluorescent light (CFL) or LED (light-emitting diode) bulb only works in touch lamps if it is labeled as dimmable. 5Unplug the touch lamp and remove the light bulb if http://homeguides.sfgate.com/reset-touch-lamp-40423.html

Touch Lamp Not Working After Blown Bulb

A great lamp for lighthouse collectors. Higher wattage dimmer switches will have better heat sinking as well which should result in the active components - the thyristors - running cooler. Squeeze the sides of the harp toward each other to release it from the harp saddle beneath the socket. 2Move the touch lamp to a work surface. tag on it said includes 60 w CFL which it didn't but I have those.

Give a healthy margin to avoid overheating. My lamp was missing one blub. Sign in 149 47 Don't like this video? Touch Lamp Turns On By Itself This works up to a point, until more than 4-5 bulbs blow out at once, then the remaining ones get too much voltage and blow out too.

An additional wire connects to the metal on the lamp. Touch Lamp Sensor With all 3 wires in each box disconnected and their ends exposed, use a tester between each one and the a earth ground (the box if metal and properly grounded). Twist the locknut counterclockwise and remove it from the nipple, using a pair of pliers.

Note: See the section: "Dimmer switches and light dimmers" if you would like to have control of brightness of a lamp or fixture from multiple locations. * For exactly two locations

The previous reply suggested that it most likely will not be worth the cost to replace the electronic sensor switch board. Touch Lamp Control Switch Take a look online also, the same options are available, however the shipping usually kills the deal. I can only plug and unplug it for the on and off function. As a side note, I have two of these identical lamps one went out and about two months later the second one.

Touch Lamp Sensor

Any suggestions??????????!! http://www.repairfaq.org/REPAIR/F_appfaq6.html The wattage of a sensor is on the plastic casing of the sensor. Touch Lamp Not Working After Blown Bulb A: The most common reasons for a blown light bulb include either cheap bulbs, loose connections in the lamp holder, a loose spring loaded connection in the bu... Touch Lamp Stays On Long term reliability is unknown for these non-supported applications.

Power surges would often switch one of my lamps, although it didn't happen often. http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html I had a pack of 4 and tried several of them - the light would come on dim at first touch but not progress any further with further touches. DetailsSet of 2 Touch Light Bulbs for OK Lighting 14 Inch Touch Lamps $9.13 In Stock.Sold by MJ World Market and ships from Amazon Fulfillment.FREE Shipping on orders over $49. Sell on Amazon Image Unavailable Image not available forColor: Touch Lamp Repair Kit by OK Lighting 4.4 out of 5 stars 99 customer reviews | 6 answered questions Price: $14.58 & How To Repair A Touch Sensitive Lamp

Jack Clark said, May 20, 2016 at 7:00 pm (Knew it already.) Simple. It is just a coincidence (or a matter of cost) that the 3-way dimmers have RFI filters and the 2-way type shown above does not. googled the SKU and it's apparently a lamp sold in 2003 at a place no longer in business. have a peek here WE love the touch sensor for turning lights on and off from the bed.

or its affiliates v DiscoverC Home Decor & Repair Crafts Food & Drink Garden Entertaining Fashion & Beauty Holidays Tech Personal Finance Cars Pets Legal Life's Moments Retirement Investing for Today Touch Lamp Control Module They also use a cheap method of crimping the wiring together in these lights. Q: What is the importance of light in our life?

Full Answer > Filed Under: Lighting Q: Why do light bulbs blow?

This releases the harp from the harp saddle beneath the socket. 8Grab the outside sleeve on the socket with your hand. Replacement parts are generally available at home centers and electrical supply houses. Turn the power back off, and hook those two wires to the two traveler terminals on the second switch. Touch Lamp Wiring Diagram But now I know for when I do have a more expensive lamp!

Make sure it's not as simple as a bad bulb or a faulty electrical outlet. Operation is otherwise identical to that of the simpler circuit. The part costs about $14 (you can probably find it cheaper, I got mine at a specialty lamp store) and you just take out the old one, keeping up with which http://techese.net/touch-lamp/touch-light-lamp-not-working.html She writes mainly home improvement, health and travel articles for various online publications.

Some touch lamps may not work if they are plugged into a dimmer switch, are using an incorrect or bad bulb or are getting interference from static electricity or radio frequency. I believe these have been replaced by the F and G suffix devices, where the F has a 25mA gate current for a fully ON state. What I Learned Today Why my touch-lamp won't turn off September 14th, 2007 at 8:45 pm (Technology, Vocabulary) I have a bedside lamp that does the cool off-low-medium-high cycle thing. Any one of those above should work in this simple circuit.

A: Bellacor is an online retailer that sells Tiffany-style lamp shades. Sorry, there was a problem. Loading... Please enter a valid US zip code.

Thank you for your feedback. They use a 100 watt sensor. With unbounded time, I'd be willing to venture into an experimental lamp-repair… for now, I'll probably make do with a different lamp I have (with a manual switch). :) Andy said, I had the same problem with my touch lamp (as the original post) and I was going to go buy different bulbs.

Time for me to buy a new lamp. Q: When was the iPod touch invented? Search DIY Guides Choose one… Electronics(696) -Gadgets(149) --iPod Touch(19) -Technology(115) --Phone(35) --Tablet(9) -Computers(158) -Remote Control (RC)(102) --Boats(12) --Buggys(2) --Cars(42) --Helicopters(16) --Planes(18) -iPhone(62) --iPhone 4(5) --iPhone 6(17) -Security(38) --CCTV(5) -Camera(13) -SatNav(25) -Electronic The wire colours are often a one-to-one swap over.

The power control transistor is the largest component on the board. It is this high current during the few milliseconds when the filament parts, that will destroy the TRIAC - it has NOTHING to do with spikes and transients coming INTO the Some assembly is required for all of our lamps. Sign in Share More Report Need to report the video?

To my dismay, when I arrived home later in the evening and tried switching the lights on, one was clearly defective. Now, at the other switch, you will find one hot.