Home > Touch Lamp > Touch Lamp Sensor Not Working

Touch Lamp Sensor Not Working

Contents

Regardless of where the touch pad is, if you take it apart it will have a set of wires coming in from 120V AC and a set of wires heading toward Q: How do you install a chandelier? within an hour would not turn off. Look inside the socket for a small brass tab. Source

Hook the other two wires in that box to the traveler terminals. Anon-chan said, June 19, 2008 at 10:26 am (Learned something new!) Actually, though most standard fluorescent bulbs don't work well with these appliances, there are fluorescent bulbs designed for multiple wattages. The lamp guy told me pretty much the same thing you suggest in your blog, but I came home anyways and googled it, and yours was the first blog that came You'll need to replace the cord if it's damaged. 2Unplug the touch lamp from the outlet.

Touch Lamp Not Working After Blown Bulb

These diagrams represent one wiring arrangement. Hope this helps. It seemed to allow the lights to work properly until we turned on the TV and the router sent out a signal. Was this answer helpful?

Quoted Text Here -- Joseph Meehan Dia duit Click to see the full signature. She writes mainly home improvement, health and travel articles for various online publications. If not worth the cost, then I will make do with only one lamp in the bedroom until the other one quits, too. Touch Lamp Control Switch so now the brand new (to me) lamp can't be turned off cuz I wrecked the sensor with the CFL.

And you'd get to solder!) wkiri said, September 15, 2007 at 12:24 pm I thought about it, as the same FAQ also notes: The specific part can be replaced but to Works like a charm; until the next time a bulb blows, I guess :) anonymous said, June 19, 2008 at 7:21 am (Knew it already.) @ Andy: Compact Fluorescent bulbs would Switch the other switch, and you'll find another hot. I've found it is easier to write down on a piece of paper what wires are hooked together before you start replacement.

Sorry, we failed to record your vote. Touch Lamp Wiring Diagram Even at around $10 a piece still beats buying a whole lamp and it will save time troubleshooting individual components I have noticed that these lamps seem to have gone out The bulbs fit perfectly in my touch lamp& the repair kit was not only extremely easy to install but my touch lamp works again after 10 years. Give a healthy margin to avoid overheating.

Touch Lamp Stays On

Once you find that one, turn the power back off, and hook that one wire to the common terminal of a switch. http://www.wkiri.com/today/?p=49 I had the same problem with my touch lamp (as the original post) and I was going to go buy different bulbs. Touch Lamp Not Working After Blown Bulb Kayte said, June 28, 2009 at 6:52 pm (Learned something new!) My own touch lamp just blew up. How To Repair A Touch Sensitive Lamp You will find one screw different from the other two.

In an OK Lighting lamp the white wire from the sensor attaches to the black wires from the base. http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html This is required by Code but allows the use of this type of wire. Comment 6 people found this helpful. Twist the locknut counterclockwise and remove it from the nipple, using a pair of pliers. Touch Lamp Control Module

There will probably be a detectable click position with the control set to full brightness if this is present. Working... Alan Chatham 67,656 views 2:15 Home Help : How to Replace a Lamp Socket - Duration: 3:23. http://techese.net/touch-lamp/touch-lamp-not-working.html Modern dimmers use a device called a triac (a type of thyristor) which is a solid state switch to control illumination by turning the light bulb on for only a part

Category Education License Standard YouTube License Show more Show less Loading... Touch Lamp Turns On By Itself How to replace a lamp switch? This is a serious safety hazard especially on older light sets that may not have internal fuses.

Is that our problem?

We invite you to learn more about Fulfillment by Amazon . dDon Goodman said, September 25, 2010 at 10:05 am (Knew it already.) What I discovered After several years of changing 10 dollar touch switches every time a bulb burnt out I in »Home Repair Touch Lamp Nightmare in »Home Repair Lady bug lamp switcher in »Home Repair Tingle from metal lamp = dangerous? Touch Lamp Sensor Wiring Diagram The red or gray wire connects to one of the lamp wires that threads through the lamp body and connects to the socket. 5Untwist the connectors that hold the lamp wires

On Sale Now 7 Answers Filter by: Most Helpful Newest Oldest Chosen Solution Ben Eisenman Rep: 84.5k 146 78 207 Posted: 01/11/2010 Options Permalink History Ultimately, I moved it to an Any idea why I might have the flicker? Sign in to add this to Watch Later Add to Loading playlists... Check This Out Note that the BT136 series can handle UP TO 4AMPS normal load, but will sometimes fail when the bulb goes, as it will only handle a maximum peak current of 25A

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Check both boxes. NOTE that the E means “sensitive gate”, and some touch lamp drive circuits need this or equivalent. These are sometimes riveted on, so you will have to drill out the rivets, and glue the base back on later ( a glue-gun is good for this).

I was able to get one for a few dollars at Lowes. Goldwasser. | [mailto].