Home > Touch Lamp > Touch Lamp Not Working After Blown Bulb

Touch Lamp Not Working After Blown Bulb

Contents

So the darn thing is an oscillator which changes frequency when you touch it. The final wire goes to the common terminal. Some fuses look like lamps - replace only with an identical fuse - not with a lamp! 7.13) Comments on Christmas tree bulb/string repair Original type of problem: No light but They've probably tried nicking a live feed from the switch( presuming its a PIR security fitting) as its near and just put the wire into the wrong terminal, easy to rectify. http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html

I bought some hanging touch lamps but didn't realize they were touch dimmers when I bought them and they hang above my head so I can't reach them. But, as others have written the most likely problem is a loose connection. Have a manual for Light Switches & Dimmers? It takes a certain amount of signal from the lamp base to switch the circuit. http://www.wkiri.com/today/?p=49

Touch Lamp Won't Turn Off

Sometimes, there are other slight variations. Calculating that a 75W lamp at 240 Volts would only dissipate 0.025 Watts. Dimmers are under the most stress and generate the most heat when operating at about 50% output.

In the other position, the connections are interchanged. And I really want LEDs to work properly, but can't understand why domestic ones don't. It seemed to allow the lights to work properly until we turned on the TV and the router sent out a signal. Touch Lamp Sensor Much handier than a new lamp or dimmer boxes Virginia B Yocham said, October 24, 2016 at 4:44 am (Knew it already.) Just an fyi- they also make a touch light

The red, black and white all had matching counterparts. Touch Lamp Control Box Replacement parts are generally available at home centers and electrical supply houses. I've tried the display and dimmer buttons and nothing happens. http://diy.stackexchange.com/questions/84505/lamps-not-working-after-blown-bulbs WARNING: Do not be tempted to bypass a bad bulb with a wire.

Oct 17, 2010 | MagLite Mag-Lite& Flashlight 2 Answers Dude. Touch Lamp Control Module I wouldn't advise anyone without experience doing repairs on a mains driven piece of kit. Brushed nickel base with a fitted cobalt glass cylinder shade. However, for one simple, if inelegant, approach to independent dimming, see the section: "Independent dimming from two locations - kludge #3251". 7.20) Simple 3-way dimmer schematic 1 The schematic below is

Touch Lamp Control Box

Then, think of the reverse: how much easier it would be to (accidentally!) touch the threaded portion. http://www.giraffeboards.com/showthread.php?t=15179 Will definitely be checking into this! Touch Lamp Won't Turn Off This is required by Code but allows the use of this type of wire. Touch Lamp Bulb Replacement Salambo View Public Profile Send a private message to Salambo Find all posts by Salambo View Blog #12 15th September 2010, 07:21 PM Wolf Larsen Charter Member Join

While designed for incandescent or heating loads only, these will generally work to some extent with universal motors as well as fluorescent lamps down to about 30 to 50 percent brightness. http://techese.net/touch-lamp/touch-light-lamp-not-working.html I have a tap switch dimmer that controls a living room wall outlet where I have a lamp plugged in. I suppose I could put an inline switch on the cable? price is only 6.5gbp. How To Repair A Touch Sensitive Lamp

Only one of these should be installed in a 3-way circuit. Glass Small Tear Drop Lamp Finial. non dimmable CF Ls dont last on a pole light sensor. http://techese.net/touch-lamp/touch-lamp-not-working.html No, it's little golf ball bulbs that go in it with a small bayonet fitting, so it's a like for like bulb.

Martin Poole said, July 13, 2011 at 11:43 am (Learned something new!) Thanks very much! Touch Lamp Stays On My bulb blew out in exactly the same way you described (bright flash -- changed lightbulb and it stayed on). Liz said, July 18, 2015 at 7:08 pm (Learned something new!) bought a new table lamp at Target today.

My lamp was missing one blub.

I know they can't be used with a dimmer switch, and I believe the touch sensitive lamps will also fail if they try to force the bulb to different levels of Work that one out! Apr 08, 2009 | Light Switches & Dimmers 1 Answer Replacing cord on table lamp From one side of the lamp cord, to one side of the switch.From other side of Touch Lamp Turns On By Itself But now I know for when I do have a more expensive lamp!

They are not supposed to leak back into the power line but they do a little. Thanks in advance. Bookmark Print Add pictures here ✖ <% if( /^image/.test(type) ){ %> <% } %> <%-name%> Add image file Upload Bold Italic Underline Upload Image Add reply Notify me about replies to Check This Out What did I do wrong.

Dismiss Notice Touch Lamp Discussion in 'Electrics UK' started by Alison556, 3 May 2008. Jeff -- Jeffry Wisnia (W1BSV + Brass Rat \'57 EE) Click to see the full signature. With all 3 wires in each box disconnected and their ends exposed, use a tester between each one and the a earth ground (the box if metal and properly grounded).