Home > Touch Lamp > Touch Base Lamp Not Working

Touch Base Lamp Not Working

Contents

With power on, only one of the 6 wires will be live. Published 5 months ago by hgwpen 5.0 out of 5 starsFive Stars worked Published 6 months ago by Amazon Customer Search Customer Reviews Search What Other Items Do Customers Buy After Justin Hulbert 51,868 views 10:24 How to Update a Light Fixture - The Home Depot - Duration: 6:04. The Better Homes and Garden website also provides a listing of retailers that sell sta... http://techese.net/touch-lamp/touch-on-off-lamp-not-working.html

Category Education License Standard YouTube License Show more Show less Loading... The bulb does seem to flicker very slightly but it does work. It fried it. Then remove the wires from the switches. you could try here

Touch Lamp Not Working After Blown Bulb

said, February 13, 2011 at 8:41 pm […] a coil of silver solder from Fry's yesterday, I was all set to make my attempt at replacing the bad triac that rendered Jess said, January 23, 2010 at 10:18 pm (Learned something new!) Had to chuckle at this, the guy at the specialty lamp store had to "remind" me that it's not the Also there the spare time factor.

With all 3 wires in each box disconnected and their ends exposed, use a tester between each one and the a earth ground (the box if metal and properly grounded). That's got to be worth some geek cred. I found the ¾ Watt was twice the size of the blown part and the ¼ Watt was 2/3 the size. Touch Lamp Control Module The red wire would then attach to the white wires from the lamp and one of the wires from the cord.

You will find one screw different from the other two. Touch Lamp Sensor Published 2 months ago by Robert Robertson 5.0 out of 5 starsPerfect fit. Yes No Sending feedback... It was beautiful, but it didn't last.

BY COINCIDENCE IT STARTED WHEN I BUNDLED WITH MY TIME WARNER PEOPLE. Touch Lamp Control Switch Same thing happened. It takes a certain amount of signal from the lamp base to switch the circuit. Now turn the power back on, and check the remaining three wires.

Touch Lamp Sensor

Worked great for a long time, but then the light started coming on all by itself…very annoying. http://www.wkiri.com/today/?p=49 When you click on a Sponsored Product ad, you will be taken to an Amazon detail page where you can learn more about the product and purchase it. Touch Lamp Not Working After Blown Bulb You may need to spread the sides with a small screwdriver to defeat the plastic clips holding the two halves together. Touch Lamp Stays On replaced bulb, it was "stuck' on, here I am!

Loading... http://techese.net/touch-lamp/touch-sensitive-lamp-not-working.html There will be one or more sockets for light bulbs - often all wired in parallel so that all the bulbs come on at the same time. Q: Where can I find table lamps? All Rights Reserved.Privacy PolicyPrivacy Policy How To Repair A Touch Sensitive Lamp

candle lamps with G9 Tungsten capsules INSIDE the main candle envelope) should find that these types tend NOT to fail and draw a large plasma-arc current, as the high-pressure halogen/xenon mixture Hoping to fix my adored touch lamp! A compact fluorescent light (CFL) or LED (light-emitting diode) bulb only works in touch lamps if it is labeled as dimmable. 5Unplug the touch lamp and remove the light bulb if have a peek here I was in tears laughing because I was in the same boat as almost everybody here!!

I guess I will take it apart one of these days and rewire with a switch because it's really a beautiful little lamp. Touch Lamp Wiring Diagram Published 3 months ago by Phil Brookhouse 4.0 out of 5 starsand easy to install It was the right part....and easy to install. Br /o---o Br o---o Br/\/o---o 3-way dimmer is up o---o/ S1 or down o---o\ S1 or Dim o---o S1 o---o \o---o o---o S2 S2 S2 However, it is still not possible

If the new lamp or appliance fails to work, the outlet may have failed or the circuit breaker tripped. 3Plug the touch lamp into a working outlet.

Sometimes when one component part burns out, it will take others with it and upon inspection they do not look burnt or show signs of damage. EDWARD said, September 15, 2012 at 1:26 pm MY LAMPS HAVE THE ADD ON TOUCH ADAPTORS AND ALL JUST STARTED WITH THIS FLICKERING PROBLEM. Please enter a valid US zip code. Touch Lamp Turns On By Itself Much handier than a new lamp or dimmer boxes Virginia B Yocham said, October 24, 2016 at 4:44 am (Knew it already.) Just an fyi- they also make a touch light

By grandma on December 3, 2015 Verified Purchase So I went with the extra 3 bulbs choice because, well the extra 3 bulbs! Will work sometimes if i hold onto something metal. Shipping was something like $6 for the whole order. http://techese.net/touch-lamp/touch-lamp-not-working.html Certainly those two parts (fusible resistor & TRIAC) are easy to replace, and if the fusible resistor protects the control IC CHIP that is a good benefit, as they are hard

you just plug the adapter into the wall and the lamp into the adapter. Your post was the first I came across when trying to figure this out. He could've easily fixed it in a matter of minutes just tinkering on Saturday afternoon… Steve said, October 7, 2013 at 11:15 pm (Learned something new!) I really enjoyed reading all Sometimes will stay off for a while, and then turns itself back on.

David said, March 15, 2010 at 2:30 pm (Learned something new!) Thanks! PB touch base lamps are just not quality as they hold them out to be. Dimmers are under the most stress and generate the most heat when operating at about 50% output. Nice to be able to repair a lamp instead of buying a new one.

The specific part can be replaced but to be sure it is bad, some testing will be needed and it is probably soldered in place. Power surges and other radio transmissions, such as ham radios, CB radios and garage door openers, can sometimes affect the lamp. Therefore, it has 3 states: Brass to Silver 1 (fully up), dim between Brass and Silver 1 (intermediate positions), and Brass to Silver 2 (fully down). Then there is the part about replacing the part with the same part or equivalent and that is possible only when you can identify the markings.

The peak current of that device is 140 AMPS! The touch-control box has four wires connected to it. She writes mainly home improvement, health and travel articles for various online publications. Was this review helpful to you?

When I refused to accept that and insisted that she replace the defective lamp with a comparable touch base lamp, she argued with us rather than replacing the lamp. The rheostat, R1, varies the amount of resistance in the RC trigger circuit.