Home > Not Working > Trailer Lights Not Working On One Side

Trailer Lights Not Working On One Side

Contents

If you have no voltage at the halfway mark, you know the fault is between there and the trailer’s connector. At the connection behind each tail lamp the new harness contains about 6 different relays on each side. Once you know which receptacle terminal is ground, switch the voltmeter to measure Volts Direct Current on the next setting above 12. Thanks asked by: Alan G
Expert Reply:This sounds like a ground problem. have a peek here

This one really has me stumped. MAY03LT 6,495 views 9:45 Trailer tail lights don't work when headlights are on fix - Duration: 1:43. We have our ground wire right here, as you can see it is loose in the air so it is not going to do you any good. Close Yeah, keep it Undo Close This video is unavailable. my company

Trailer Lights Not Working Properly

Today, 10:38 PM Are the hours stored in the ecu or the gauge cluster? We're measuring ohms, so if there are more than two holes for the leads, plug the red one in by the omega symbol. 4. By jasonbedell in forum Kawasaki PWC Performance (4-stroke) Replies: 7 Last Post: 07-23-2007, 08:52 PM Trailer Lights By pauladave in forum Yamaha Open Discussion Replies: 10 Last Post: 03-21-2007, 03:32 PM Now retest the problem.

I then redid the ground on the truck's converter box, and then my light testing of the truck's plug was consistent with what I saw on the trailer - nothing from William Quinn 170,075 views 11:19 Chevrolet Silverado Trailer 12 Volt Accessory Fuse - Winch Battery Charging - Duration: 9:12. Make sure the connection point is free of rust and corrosion as that could cause a bad ground.The driver side light should have a yellow and brown wire connected. Left Running Light On Trailer Not Working etrailer.com 31,182 views 3:36 This Old Trailer: Finding and Fixing Wiring Shorts - etrailer.com - Duration: 5:25.

Good Luck. Trailer Running Lights Not Working One Side And that is the proper way how the trailer should be hooked up to the tow vehicle. 1:19Just to give you a quick idea how electricity flows in the trailer what Then hooked up all three vehicles to utiliy trailer and nothing worked right . https://www.etrailer.com/question-100828.html So in total I guess I had a bad converter, no ground past the trailer tilt point, and intermittent ground initially at the ball.

Join Date Mar 2009 Location MA Posts 4,006 +1169 Yup in my experience, its always the ground that causes the lights not to work. One Trailer Brake Light Not Working The easiest way to visualize it is that a stream of electrons leaves the battery's positive terminal and travels through the on/off switch (your running lights switch, turn signal or brake William Quinn 170,075 views 11:19 How to Install New Taillights on a Utility Trailer - Duration: 5:21. Trailer light grounding: Trace the White wire back from the connector to the trailer.

Trailer Running Lights Not Working One Side

Check the ground or white wire connection to each lamp. Someone mentioned fuses. Trailer Lights Not Working Properly Reply With Quote 04-30-2011,02:20 PM #3 Xrunner View Profile View Forum Posts Private Message Join Date Dec 2010 Location Columbia river Posts 285 +11 Originally Posted by K447 I would think Right Turn Signal On Trailer Not Working Next move to the lights themselves.

only right side works.? navigate here My Van is a 2000 year model. So its all good now. Any ideas? Left Side Trailer Lights Don't Work

Add to Want to watch this again later? Use a test light at the plug checking all the wires then work back to the lights on the trailer. Other than the initial cost of LEDs, which is higher than that of traditional incandescent bulbs, there are few downsides to the new technology, especially for boat trailer applications.An LED is Check This Out Considering a GSXL or XPL Today, 10:26 PM Most Views GreenHulk's GP1800 build up thread Last Post By Green Hulk (59 replies) Today, 07:57 PM in Yamaha PWC Performance (4-stroke) Unlimited

The second way is the tail lamp assembly is grounded through the mounting bolt that attaches the tail light to the frame.You will also want to check the ground at the Trailer Brake Lights Dont Work Oh yeah, and one time when I changed a light bulb on the trailer my truck's clock would blink when I put the right turn signal on. Originally posted by SwampThing View Post Is this a new vehicle + trailer set up?

This happens when the ground is not solid enough to pass the full required current for all lights, but only enough for some.

Loading... click here.Products Referenced in This QuestionReplacement Side Marker Light Bulb # 194 42 reviewsCode: A194BPrice:$0.85Accessories and PartsTrailer LightsLight BulbsClearOptronicsmore information > Double Bullseye Trailer Clearance, Side Marker Light, Two-Bulb - Red It can happen that if the main ground is not 100-percent solid, some but not all lights will function. Trailer Brake Lights And Turn Signals Not Working The days of just crimping into the tail light harness are long gone.

O4 FX HO Where are hours stored,... By delagem in forum Polaris Open Discussion Replies: 5 Last Post: 07-15-2008, 09:11 PM Trailer Lights By blegan in forum Towing and Trailers Replies: 3 Last Post: 05-20-2008, 04:33 PM Problem A study by the University of Michigan's Transportation Research Institute found that LED lamps respond, on an average, 1/5-of-a-second faster than standard incandescent lamps. this contact form You can only upload photos smaller than 5 MB.

ok. ... Tags: None Seon Petty Officer 1st Class Join Date: Apr 2008 Posts: 297 #2 April 12th, 2011, 01:54 PM Re: left turn signal and brake light not working on trailer Check etrailer.com 99,852 views 5:25 Utility Trailer 03 - 4 Pin Trailer Wiring and Diagram - Duration: 28:42. Comment Cancel Post 2 Eagles Petty Officer 1st Class Join Date: Apr 2011 Posts: 206 #4 April 12th, 2011, 04:02 PM Re: left turn signal and brake light not working on

Sign in Share More Report Need to report the video? Autoplay When autoplay is enabled, a suggested video will automatically play next. The first way is the tail light assemblies can be grounded by a separate wire coming out of the back of the tail light and attached to the trailers frame. Keep the trailer connector plugged in.

The white wire on the trailer is the ground.and has to be connected as the ball might have rust and not making a good connection. Ciaran O · 7 years ago 0 Thumbs up 0 Thumbs down Comment Add a comment Submit · just now Report Abuse High Performance Tactical Flashlight - http://FlashLight.uzaev.com/?EWBW Marianne · 4 Boat trailer running lights work will not blink/brake? BigjermsGarage 97,153 views 9:12 CHEVROLET 2007 SILVERADO TRAILER LIGHT TROUBLESHOOTING - Duration: 2:34.

This feature is not available right now. We're testing to see if power is getting to the receptacle. 7. I looked further and it seems as though the middle lead looks broken at the bottom where I guess it would return to ground for the directional. The metal frame and all metal touching it is the "common" (another name for ground) path through which the electricity returns to the battery.